Debian – Page 2 – More Zonkyness

Debian: Testing The Resilience Of A Mirrored Installation

Computing, Linux, Working Notes No Responses »

Aug 022014

One of the questions I always ask myself when setting up a resilient server, is just how well will it cope with a disk failure? Ultimately you cannot answer that without trying it out.

But as practice (and to determine whether it mostly works), it’s perfectly sensible to try it out on a virtual machine.

Debian Installation

If you are looking for full instructions on installing Debian, this is not the place to look. I configured the virtual machine with 2GBytes of memory, an LsiLogic SAS controller with two attached disks each of 64GBytes.

The installation process was much as per normal (I unselected “Desktop” to save time), but the storage was somewhat different :-

Manual partitioning method
Create an empty partition on both disks
Select Software RAID
Create an MD device
RAID1
And put both disks into the RAID
Configure LVM
Create a Volume Group (“sys”)
Select md0 for the volume group device
Create logical volumes (boot: 512MB, root: 16GB, var: 8GB, home: 512M (it’s a server))
In the partitioning manager select each Logical Volume in turn and specify the file system parameters.

You will notice that no swap was created – this was a mistake that I’m in the unfortunate habit of making! However for a test, it wasn’t a problem and with LVM it is possible to create swap after the installation.

Post Installation

After the server has booted, it is possible to check the second hard disk for the presence of grub in the MBR (dd if=/dev/sdb of=/var/tmp/sdb.boot bs=1M count=1, and then run strings on the result). It turns out that nothing is installed in the MBR of the second disk by default. Which would make booting in a degraded environment an interesting challenge (i.e. you’ll have to find a rescue CD and boot off the relevant hard disk).

However this can be fixed by installing grub onto the second hard disk: grub-install /dev/sdb

Testing Resilience

But what happens when you lose a disk? Now is the time to test. Shut down the virtual machine and remove the second hard disk – leaving the first hard disk in place does not provide a full test.

If your first attempt at booting afterwards results in a failure to acquire a grub menu, then either you have failed to run grub-install as detailed above (guess what mistake I made?), or your BIOS settings don’t permit the computer to boot off anything other than the first hard disk.

However, in my second attempt, the server booted normally with the addition of a few messages that indicate that there is just one disk making up the mirrored pair.

Summary

Yes, you can put /boot onto an LVM file system that sits on mirrored disks. That hasn’t always been the case.
It is still necessary to run grub-install to put Grub onto the MBR of the second hard disk.
It works.

Dual InfiniBand Links At Home

Computing, Working Notes No Responses »

Jul 292013

… which is of course massive overkill. But fun. It should increase the raw bandwidth available between the two machines from 1Gbps to 20Gbps (with one link) and 40Gbps with both links bonded. It was a bit of a surprise to me when I looked around at prices of second-hand kit to realise that InfiniBand was so much cheaper to acquire than Fibre Channel; the kit I acquired cost less than £100 all in whereas FC kit would be in the region of £1,000, and InfiniBand is generally quicker. There is of course 16Gb FC and 10Gb InfiniBand, but that is hardly comparing like with like. So what is this overkill for? Networking of course. I’ve acquired two HP InfiniBand dual link cards which means I can connect my workstation to my server :- Using dual links is of course overkill on top of overkill, but given that these cards have dual links, why not use them? And it does give a couple of experiments to try later. To prepare in advance, the following network addresses will be used :-

Server	Link Number	IPv4 Address	IPv6 Address
A	1	10.255.0.1	AAISP:d00d::1
A	2	10.255.1.1	AAISP:d00f::1
B	1	10.255.0.254	AAISP:d00d:2
B	1	10.255.1.254	AAISP:d00f:2

Yes I have cheated for the IPv6 addresses! The first step is to configure each “server” … one is running Debian Linux, and the other is running FreeBSD.

Configuring Linux

This was subject to much delay whilst I believed that I had a problem with the InfiniBand card, but putting the card into a new desktop machine caused it to spring back to life. Either some sort of incompatibility with my old desktop (which was quite old), or some sort of problem with the BIOS settings.

Inserting the card should load the core module (mlx4_core) automatically, and spit out messages similar to the following :-

[    3.678189] mlx4_core 0000:07:00.0: irq 108 for MSI/MSI-X
[    3.678195] mlx4_core 0000:07:00.0: irq 109 for MSI/MSI-X
[    3.678199] mlx4_core 0000:07:00.0: irq 110 for MSI/MSI-X
[    3.678204] mlx4_core 0000:07:00.0: irq 111 for MSI/MSI-X
[    3.678208] mlx4_core 0000:07:00.0: irq 112 for MSI/MSI-X
[    3.678212] mlx4_core 0000:07:00.0: irq 113 for MSI/MSI-X
[    3.678216] mlx4_core 0000:07:00.0: irq 114 for MSI/MSI-X
[    3.678220] mlx4_core 0000:07:00.0: irq 115 for MSI/MSI-X
[    3.678223] mlx4_core 0000:07:00.0: irq 116 for MSI/MSI-X
[    3.678228] mlx4_core 0000:07:00.0: irq 117 for MSI/MSI-X
[    3.678232] mlx4_core 0000:07:00.0: irq 118 for MSI/MSI-X
[    3.678236] mlx4_core 0000:07:00.0: irq 119 for MSI/MSI-X
[    3.678239] mlx4_core 0000:07:00.0: irq 120 for MSI/MSI-X
[    3.678243] mlx4_core 0000:07:00.0: irq 121 for MSI/MSI-X
[    3.678247] mlx4_core 0000:07:00.0: irq 122 for MSI/MSI-X
[    3.678250] mlx4_core 0000:07:00.0: irq 123 for MSI/MSI-X
[    3.678254] mlx4_core 0000:07:00.0: irq 124 for MSI/MSI-X
[    3.678259] mlx4_core 0000:07:00.0: irq 125 for MSI/MSI-X
[    3.678263] mlx4_core 0000:07:00.0: irq 126 for MSI/MSI-X
[    3.678267] mlx4_core 0000:07:00.0: irq 127 for MSI/MSI-X
[    3.678271] mlx4_core 0000:07:00.0: irq 128 for MSI/MSI-X
[    3.678275] mlx4_core 0000:07:00.0: irq 129 for MSI/MSI-X

This is just the core driver; at this point additional modules are needed to do anything useful. You can manually load the modules with modprobe but sooner or later it is better to make sure they’re loaded automatically by adding their names to /etc/modules. The modules you want to load are :-

mlx4_ib
ib_umad
ib_uverbs
ib_ipoib

This is a minimal set necessary for networking (“IP”) rather than additional features such as SCSI. It’s generally better to start with a minimal set of features initially. At this point, it is generally a good idea to reboot to verify that things are getting closer. After a reboot, you should have one or more new network interfaces listed by ifconfig :-

ib0       Link encap:UNSPEC  HWaddr 80-00-00-48-FE-80-00-00-00-00-00-00-00-00-00-00  
          UP BROADCAST RUNNING MULTICAST  MTU:2044  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:256 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ib1       Link encap:UNSPEC  HWaddr 80-00-00-49-FE-80-00-00-00-00-00-00-00-00-00-00  
          UP BROADCAST RUNNING MULTICAST  MTU:2044  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:256 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Despite the appearance, we still have quite a way to go yet. The next step is to install some additional packages: ibutils, infiniband-diags, and opensm. The last package is for a subnet manager which is unnecessary if you have an InfiniBand switch (but I don’t). The first step is to get opensm up and running. Edit /etc/default/opensm and change the PORTS variable to “ALL” (unless you want to restrict the managed ports, and make things more complicated). And start opensm: /etc/init.d/opensm start; update-rc.d opensm defaults.

At this point, you can configure the network addresses by editing /etc/network/interfaces. If you need help doing this, then you’re in the tech pool beyond your depth! Without something at the other end, these interfaces won’t work (obviously), so it’s time to start work on the other end …

Configuring FreeBSD

See: https://wiki.freebsd.org/InfiniBand I hadn’t had cause to build a custom kernel before, so the very first task was to use subversion to checkout a copy of the FreeBSD source code :-

svn co svn://svn0.us-east.FreeBSD.org/base/stable/9 /usr/src

Updating will of course require just: cd /usr/src && svn update. Once installed, create a symlink from /sys to /usr/src/sys if the link does not already exist: ln -s /usr/src/sys /sys

Go to the kernel configuration directory (/usr/src/sys/amd64/conf), copy the GENERIC configuration file to a new file, and edit the new file to add in certain options :-

# Infiniband stuff (locally added)
options         OFED
options         IPOIB_CM
device          ipoib
device          mlx4ib

Again, this is a minimal set that will not offer full functionality … but should be enough to get IP networking up and running. The next step is to build and install the kernel :-

make buildkernel KERNCONF=${NAME-OF-YOUR-CONFIG}; make installkernel KERNCONF=${NAME-OF-YOUR-CONFIG}

The next step is to build the “world” :-

Edit /etc/src.conf and add “WITH_OFED=’yes'” to that file.
Change to /usr/src and run: make buildworld
Finalise with make installworld

As it happens I had to build the user-land first, as the kernel compilation needed a new user-land feature.

After a reboot, the new network interface(s) should show up as ib0 upwards. And these can be configured with an address in exactly the same as any other network interface.

Testing The Network

A tip for making sure the interfaces you think are connected together is to configure one of the machines, send a broadcast ping to the relevant network address of each interface in turn, and run tcpdump on the other machine to verify that the packets coming down the wire match what you expect.

Below the level of IP, it is possible to run an InfiniBand ping to verify connectivity. First you need a GUID on “the server”, which can be obtained by running ibstat and looking for the “Port GUID”, which will be something like “0x0002c90200273985”. Next run ibping -S on the server.

Now on the other machine (“the client”), run ibping :-

# ibping -G 0x0002c90200273985
Pong from polio.inside.zonky.org (Lid 3): time 0.242 ms
Pong from polio.inside.zonky.org (Lid 3): time 0.153 ms
Pong from polio.inside.zonky.org (Lid 3): time 0.160 ms

The next step is to run an IP ping to one of the hosts. If that works, it is time to start looking at something that will do a reasonable attempt at a speed test.

This can be done in a variety of different ways, but I chose to use nttcp which is widely available. On one of the hosts, run nttcp -i to act as the “partner” (or server). On the sending server, run nntcp -T ${ip-address-to-test} which will give output something like :-

# nttcp -T 10.0.0.26
     Bytes  Real s   CPU s Real-MBit/s  CPU-MBit/s   Calls  Real-C/s   CPU-C/s
l  8388608    0.70    0.01     95.7975   5592.4053    2048   2923.51  170666.7
1  8388608    0.71    0.04     94.0667   1878.6950    5444   7630.87  152403.3

According to the documentation, the second line should begin with ‘r’, but for a simple speed test we can simply average the numbers in the “Real-MBit/s” to get an approximate speed. Oddly my gigabit ethernet seems to have mysteriously degraded to 100Mbps! At least it makes the InfiniBand speed slightly more impressive :-

# nttcp -T 10.255.0.2
     Bytes  Real s   CPU s Real-MBit/s  CPU-MBit/s   Calls  Real-C/s   CPU-C/s
l  8388608    0.03    0.00   2521.9415  16777.2160    2048  76963.55  512000.0
1  8388608    0.03    0.03   2206.6574   2568.6620    4032 132579.25  154329.0

Before getting into a panic over what appears to be a pretty poor result, it is worth bearing in mind that IP over InfiniBand isn’t especially efficient, and InfiniBand seems to suffer from marketing exaggeration. From what I understand, DDR’s 20Gbps signalling rate becomes 16Gbps, which in turn becomes 8.5Gbps when looking at the output of ibstatus (not ibstat) – why the halving here is a bit of a mystery, but that may become apparent later.

There has also been a hint that FreeBSD is due for a significant improvement in InfiniBand performance sometime after the release of 9.2.

As a late addition, it would appear that running OpenSM (the subnet manager) on both hosts means that when one or other is rebooting, the other can take over the duties of the subnet manager. To enable on FreeBSD, simply add opensm_enable=”YES” to the file /etc/rc.conf and reboot.

Debian: Adding Entropy to /dev/random

Computing, Linux, Security 1 Response »

Oct 172012

I have recently become interested in the amount of entropy available in Linux and decided to spend some time poking around on my Debian workstation. Specifically looking to increase the amount of entropy available to improve the speed of random number generation. There are a variety of different ways of accomplishing this including hardware devices (some of which cost rather too much for a simple experiment).

Eh?

Linux has a device (/dev/random) which makes available random numbers to software packages that really need access to a high quality source of random numbers. Any decently written cryptographic software will use /dev/random (and not /dev/urandom which does not generate “proper” random numbers of quality) to implement encryption.

Using poor quality random numbers can potentially result in encryption not being secure. Or perhaps more realistically, because Linux waits until there is sufficient entropy available before releasing numbers through /dev/random, software reading from that device may be subject to random stalling. Not necessarily long enough to cause a major problem, but perhaps enough to have an effect on performance.

Especially for a server in a virtualised environment!

Adding Entropy The Software Way (haveged)

HAVEGED is a way of using processor flutter to add entropy to the Linux /dev/random device. It can be installed relatively easily with :-

apt-get install haveged
/etc/init.d/haveged start

As soon as this was running the amount of entropy available (cat /proc/sys/kernel/random/entropy_avail) jumped from several hundred to close to 4,000.

Now does this increased entropy have an effect on performance? Copying a CD-sized ISO image file using ssh :-

Default entropy	29.496
With HAVEGED	28.636

A 2% improvement in performance is hardly a dramatic improvement, but every little bit helps and it may well have a more dramatic effect on a server which regularly exhausts entropy.

Checking The Randomness

But hang on … more important than performance is the randomness of the numbers generated. And you cannot mess with the generation of random numbers without checking the results. The first part of checking the randomness is making sure you have the right tools installed :-

apt-get install rng-tools

Once installed you can test the current set of random numbers :-

dd if=/dev/random bs=1k count=32768 iflag=fullblock| rngtest

This produces a whole bunch of output, but the key bits of output are the “FIPS 140-2 failures” and “FIPS 140-2 successes”; if you have too many failures something is wrong. For the record my failure rate is 0.05% with haveged running (without: tests ongoing).